[Nov 09, 2024] Latest 300-430 Exam with Accurate Implementing Cisco Enterprise Wireless Networks PDF Questions
Practice To 300-430 - TopExamCollection Remarkable Practice On your Implementing Cisco Enterprise Wireless Networks Exam
Obtaining the CCNP Enterprise certification proves that the professionals have the expertise in enterprise networking solutions. To earn this certificate, the applicants are required to pass two exams. One of them covers core enterprise technologies, while the second is a concentration test (there are six exams of this category for this path) of your choice. Cisco 300-430 will evaluate your skills and knowledge of the implementation of the wireless network. Completing this test allows you to get the Cisco Certified Specialist – Enterprise Wireless Implementation certification, in addition to CCNP Enterprise.
Cisco 300-430 exam is a part of the Cisco Certified Specialist - Enterprise Wireless Implementation certification. It is designed to test the knowledge and skills of the candidates in implementing Cisco Enterprise Wireless Networks. 300-430 exam is designed for professionals who are responsible for designing and implementing wireless networks in an enterprise environment.
NEW QUESTION # 99
Refer to the exhibit.
An engineer implemented the CPU ACL on your Cisco
5520 Series Wireless LAN Controller, and the controller is no longer
manageable via the network What must be changed on this CPU ACL to
enable it to manage the controller again?
- A. Permit statements must be added to the top of the ACL in both directions, which specify the network to be managed from and the virtual interface of the controller.
- B. Line 1 must be set to a destination port of HTTP
- C. Permit statements must be added to the top of the ACL, which specify the network to be managed from
- D. Line 1 must be set to the inbound direction. 2
Answer: A
NEW QUESTION # 100
An engineer enabled Cisco Centralized Key Management (CKM) on a WLAN with local and FlexConnect mode APs. The engineer notices that Cisco CKM is not working for the FlexConnect APs when looking at roaming, but it works for local mode APs. Which change must be made on the controller for the configuration to work properly?
- A. Configure VLAN-based central switching.
- B. Enable Cisco FlexConnect Central Assoc.
- C. Place APs in a Cisco FlexConnect group.
- D. Use local authentication.
Answer: C
Explanation:
FlexConnect groups are responsible for sharing services between APs in the group. For example, the following services are shared within a FlexConnect group:
Cisco Centralized Key Management (CCKM) / Opportunistic Key
Caching (OKC) fast roaming keys
Local/backup RADIUS server keys
Local EAP (Extensible Authentication Protocol) authentication
Smart Image upgrade
FlexConnect AVC (Application Visibility and Control)
AAA-Override for local switching
NEW QUESTION # 101
A wireless engineer must configure access control on a WLC using a TACAS+ server for a company that is implementing centralized authentication on network devices. Which role must be configured under the shell profile on the TACAS+ server for a user with ready-only permissions?
- A. MONITOR
- B. MANAGEMENT
- C. READ
- D. ADMIN
Answer: A
NEW QUESTION # 102
A new MSE with wIPS service has been installed and no alarm information appears to be reaching the MSE from controllers. Which protocol must be allowed to reach the MSE from the controllers?
- A. NMSP
- B. CAPWAP
- C. SOAP/XML
- D. SNMP
Answer: A
Explanation:
https://www.cisco.com/c/en/us/td/docs/wireless/mse/7-6/MSE_wIPS/MSE_wIPS_7_6/MSE_wIPS_7_5_chapter_01000.html
NEW QUESTION # 103 
Refer to the exhibit. Which two items must be supported on the VoWLAN phones to take full advantage of this WLAN configuration? (Choose two.)
- A. SIFS
- B. TSPEC
- C. WMM
- D. APSD
- E. 802.11e
Answer: C,E
NEW QUESTION # 104
A company has a Cisco wireless network with Cisco ISE. The company wants to allow employees to use their personal mobile devices on the wireless network. The company wants to allow access to the network only if the devices meet certain criteria. To meet the requirement, the company asked a network engineer to create a native supplicant profile. Which two fields must be configured when the profile is created? (Choose two.)
- A. Allowed Protocol (LEAP/ EAP-TTLS)
- B. SSID Name
- C. Allowed Protocol (PEAP/TLS)
- D. WLC Name
- E. Allowed Protocol (Ms-CHAPv2/ EAP-FAST)
Answer: A,B
NEW QUESTION # 105
What is the difference between PIM sparse mode and PIM dense mode?
- A. Sparse mode supports only one switch. Dense mode supports multiswitch networks.
- B. Sparse mode supports multiswitch networks. Dense mode supports only one switch.
- C. Sparse mode floods. Dense mode uses distribution trees.
- D. Sparse mode uses distribution trees. Dense mode floods.
Answer: D
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipmulti_pim/configuration/xe-16/imc-pim-xe-16-book/imc-te In Sparse mode packets branches distribution growth as new nodes join the multicast group.
https://community.calix.com/s/article/Dense-Mode-Multicast-vs-Sparse-Mode-Multicast-1
NEW QUESTION # 106
An engineer configures a deployment to support:
* Cisco CMX
* licenses for at least 3000 APs
* 6000 wIPS licenses
The Cisco vMSE appliance must be sized for this deployment. Which Cisco vMSE Release 8 option must the engineer deploy?
- A. High-End vMSE
- B. Low-End vMSE
- C. Large vMSE
- D. Standard vMSE
Answer: A
Explanation:
Explanation
Table Description automatically generated
NEW QUESTION # 107
Refer to the exhibit.
An engineer tries to manage the rogues on the Cisco WLC. Based on the configuration, which AP is marked as malicious by the controller?
- A. rogue AP with SSlD admin seen for 4000 seconds and heard at -70 dBm
- B. rogue AP with SSlD admin seen for 4000 seconds and heard at -60 dBm
- C. rogue AP with SSID admin seen for 3000 seconds and heard at -60 dBm
- D. rogue AP with SSID admin seen for 3000 seconds and heard at -70 dBm
Answer: D
Explanation:
NEW QUESTION # 108
Refer to the exhibit.
Which two items must be supported on the VoWLAN phones to take full advantage of this WLAN configuration? (Choose two.)
- A. SIFS
- B. TSPEC
- C. WMM
- D. APSD
- E. 802.11e
Answer: C,E
Explanation:
NEW QUESTION # 109
Which three properties are used for client profiling of wireless clients? (Choose three.)
- A. MAC OUI
- B. hostname
- C. HTTP user agent
- D. DHCP
- E. IP address
- F. OS version
Answer: A,C,D
NEW QUESTION # 110
An engineer must implement rogue containment for an SSID. What is the maximum number of APs that should be used for containment?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
Explanation:
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/wireless/technology/roguedetection_deploy/ Rogue_Detection.html
NEW QUESTION # 111
A Cisco WLC has been added to the network and Cisco ISE as a network device, but authentication is failing.
Which configuration within the network device configuration should be verified?
- A. device ID
- B. device interface credentials
- C. shared secret
- D. SNMP RO community
Answer: C
Explanation:
NEW QUESTION # 112
An engineer is designing a high availability wireless network. What mechanism should be the focus for high availability?
- A. RSSI
- B. cell overlap
- C. channel reuse
- D. SNR
Answer: B
Explanation:
Describe basic RF deployment considerations related to site survey design of data or VoWLAN applications, common RF interference sources such as devices, building material, AP location, and basic RF site survey design related to channel reuse, signal strength, and cell overlap. If an AP fails, channel reuse in the design is not going to help you if there is no coverage. Cell overlap will, because more than one AP will cover a given area.
NEW QUESTION # 113
An engineer is performing a Cisco Hyperlocation accuracy test and executes the cmxloc start command on Cisco CMX. Which two parameters are relevant? (Choose two.)
- A. X, Y real location
- B. client MAC address
- C. WLC IP address
- D. client description
- E. AP name
Answer: A,B
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/88/b_ap_4800_hyperlocation_deployment_g
NEW QUESTION # 114
Refer to the exhibit.
An engineer deployed a Cisco WLC using local EAP. Users who are configured for EAP-PEAP cannot connect to the network. Based on the local EAP debug on the controller provided, why is the client unable to connect?
- A. The user is using invalid credentials.
- B. The client is failing to accept certificate.
- C. The Cisco WLC local EAP profile is misconfigured.
- D. The Cisco WLC is configured for the incorrect date.
Answer: B
NEW QUESTION # 115
An engineer must implement intrusion protection the WLAN. The AP coverage is adequate and on-channel attacks are the primary concern. The building is historic, which makes adding APs difficult. Which Ap mode and submode must be implemented?
- A. Ap mode: local, Ap submode: none
- B. Ap mode: local, Ap submode: WIPS
- C. Ap mode: monitor, Ap submode: WIPS
- D. Ap mode: monitor, Ap submode: none
Answer: B
Explanation:
NEW QUESTION # 116
An engineer is ensuring that, on the IEEE 802.1X wireless network, clients authenticate using a central repository and local credentials on the Cisco WLC. Which two configuration elements must be completed on the WLAN? (Choose two.)
- A. MAC authentication
- B. web authentication
- C. local EAP enabled
- D. LDAP server
- E. TACACS+
Answer: B,E
NEW QUESTION # 117
......
Exam Questions and Answers for 300-430 Study Guide Questions and Answers!: https://www.topexamcollection.com/300-430-vce-collection.html
Practice To 300-430 - TopExamCollection Remarkable Practice On your Implementing Cisco Enterprise Wireless Networks Exam: https://drive.google.com/open?id=1hdMgCAJQNU5wyvpQzzXJbdAT36IybOIK
