Dec 18, 2024 PASS EMC D-PSC-MN-23 EXAM WITH UPDATED DUMPS
D-PSC-MN-23 Questions PDF [2024] Use Valid New dump to Clear Exam
NEW QUESTION # 78
In PowerScale hardware maintenance, why is it essential to track the installation and maintenance of FRUs?
- A. To provide a history for troubleshooting and diagnostics
- B. To maintain a detailed inventory for audit purposes
- C. To ensure optimal data placement within the cluster
- D. To facilitate future software upgrades
Answer: B
NEW QUESTION # 79
Before replacing any CRUs in a PowerScale node, what is an important safety measure?
- A. Documenting the serial numbers of all components
- B. Verifying the node's data is fully replicated to other nodes
- C. Ensuring the node is logically removed from the cluster
- D. Powering down the node and disconnecting it from the network
Answer: D
NEW QUESTION # 80
What are the essential verifications after preparing a PowerScale node for operation? (Select two)
- A. Cluster membership is intact.
- B. License keys are validated.
- C. There are no pending alerts.
- D. Data rebalancing is complete.
Answer: A,C
NEW QUESTION # 81
Which network configurations are valid on a Dell PowerScale Gen 6 cluster that uses an Ethernet backend?
- A. IPv4 or IPv6 addressing, 1500 MTU, and 24-bit subnet mask
- B. IPv6 addressing only, 1500 MTU, and 48-bit subnet mask
- C. IPv4 addressing only, 9000 MTU, and 24-bit subnet mask
- D. IPv4 addressing only, 1500 MTU, and 48-bit subnet mask
Answer: C
NEW QUESTION # 82
What distinguishes PowerScale Gen 6 nodes from earlier generations?
- A. They have higher storage density.
- B. They provide enhanced virtualization support.
- C. They offer better energy efficiency.
- D. They feature a more robust operating system.
Answer: A
NEW QUESTION # 83
What is a precaution when working with Dell PowerScale equipment?
- A. Nodes can operate below 5 degrees C, but only for limited periods of time
- B. Connections to the branch circuit need not be properly grounded
- C. Use side stabilizers if the rack is not bolted to the floor
- D. The total rack load should not exceed 70% of the branch circuit rating
Answer: A
NEW QUESTION # 84
A platform engineer plans to set up a rack system for a Dell PowerScale cluster installation.
What is a requirement for the initial setup?
- A. Power cords must be connected to four power distribution units within the rack cabinet.
- B. The rack cabinet must have at least dual power supplies with power distribution.
- C. Grounding lugs must be used for internal grounding within the chassis.
- D. The rack system must have twelve independent 200-240 V power sources.
Answer: B
NEW QUESTION # 85
A Dell PowerScale platform engineer has executed the shutdown command on a three-node cluster.
The shutdown sequence displays an error and appears unresponsive.
How should the platform engineer address this issue?
- A. Contact Dell Technical Support for assistance.
- B. Execute a hardware shutdown by pressing the power button three times within five seconds.
- C. Hold the power button down until the node completes shutdown.
- D. Remove power cables separately, waiting at least five seconds between removing each of them.
Answer: A
NEW QUESTION # 86
How do you ensure data continuity during a PowerScale node hardware upgrade?
- A. Synchronize all nodes before starting the upgrade
- B. Isolate the node being upgraded from the network
- C. Implement rolling upgrades across the cluster
- D. Use data mirroring to an external backup cluster
Answer: C
NEW QUESTION # 87
Which Dell PowerScale interface is the simplest to use for customers?
- A. OneFS command line
- B. Platform application interface
- C. Serial console
- D. Web administration interface
Answer: D
NEW QUESTION # 88
What are essential steps when creating a new PowerScale cluster?
- A. Configuring network settings
- B. Enabling compliance features
- C. Assigning cluster name and IP pool
- D. Setting up data protection levels
Answer: A,C,D
NEW QUESTION # 89
When reimaging a node in the context of PowerScale, what is the primary goal?
- A. To update the node's BIOS settings
- B. To ensure the node's firmware is up to date
- C. To install a new operating system version
- D. To restore the node's original factory settings
Answer: C
NEW QUESTION # 90
A platform engineer plans to upgrade Dell PowerScale OneFS.
Which action must they consider during the pre-upgrade phase?
- A. Update firmware
- B. Check supportability and compatibility requirements
- C. Implement OneFS API
- D. Install recommended patches
Answer: A
NEW QUESTION # 91
A customer is planning to add a node to a Dell PowerScale cluster running OneFS 9.0.
Which command can they use from the CLI?
- A. isi devices -add
- B. isi devices node add --serial-number=<SN>
- C. isi node add --node-lnn
- D. isi devices node add --node-lnn
Answer: B
NEW QUESTION # 92
Which tools are used for managing a PowerScale cluster? (Select two)
- A. SNMP Manager
- B. PAPI
- C. CLI
- D. WebUI
Answer: C,D
NEW QUESTION # 93
A platform engineer has added an F200 node to a Dell PowerScale cluster. The cluster now has five F200 nodes.
Before leaving the site, what action must they perform?
- A. Reboot the node and wait for a green status
- B. Ensure the node LNN is set to 1
- C. SmartFail the node and rejoin to the cluster
- D. Test for node connectivity and normal function
Answer: D
NEW QUESTION # 94
......
D-PSC-MN-23 Study Guide Brilliant D-PSC-MN-23 Exam Dumps PDF: https://www.topexamcollection.com/D-PSC-MN-23-vce-collection.html
Passing EMC D-PSC-MN-23 Exam Using 2024 Practice Tests: https://drive.google.com/open?id=139Z--5YeFOW9vAUcWNDtdsLiqGXdCxkf
