Best Fortinet NSE7_LED-7.0 2024 Training With 40 QA's
Fortinet NSE7_LED-7.0 Certification Exam Questions
NEW QUESTION # 11
Refer to the exhibit.
Examine the FortiSwitch security policy shown in the exhibit
If the security profile shown in the exhibit is assigned to all ports on a FortiSwitch device for 802 1X authentication which statement about the switch is correct?
- A. FortiSwitch will assign non-802 1X devices to the onboarding VLAN
- B. All EAP messages will be terminated on FortiSwitch
- C. FortiSwitch will try to authenticate non-802 1X devices using the device MAC address as the username and password
- D. FortiSwitch cannot authenticate multiple devices connected to the same port
Answer: A
Explanation:
Explanation
According to the FortiSwitch Administration Guide, "If a device does not support 802.1X authentication, you can configure the switch to assign the device to an onboarding VLAN. The onboarding VLAN is a separate VLAN that you can use to provide limited network access to non-802.1X devices." Therefore, option C is true because it describes the behavior of FortiSwitch when the security profile shown in the exhibit is assigned to all ports. Option A is false because FortiSwitch can authenticate multiple devices connected to the same port using MAC-based or MAB-EAP modes. Option B is false because FortiSwitch will not try to authenticate non-802.1X devices using the device MAC address as the username and password, but rather use MAC authentication bypass (MAB) or EAP pass-through modes. Option D is false because all EAP messages will be terminated on FortiGate, not FortiSwitch, when using 802.1X authentication.
NEW QUESTION # 12
Refer to the exhibit
A device connected to port2 on FortiSwitch cannot access the network The port is assigned a security policy to enforce 802 1X authentication While troubleshooting the issue, the administrator obtains the debug output shown in the exhibit Which two scenarios are likely to cause this issue? (Choose two.)
- A. The device has been assigned the guest VLAN
- B. The device has been quarantined for 3600 seconds.
- C. The device is not configured for 802 IX authentication.
- D. The device does not support 802 1X authentication
Answer: C,D
Explanation:
Explanation
According to the exhibit, the debug output shows that the device connected to port2 on FortiSwitch is sending an EAPOL-Start message, which is the first step of the 802.1X authentication process. However, the output also shows that the device is not sending any EAP-Response messages, which are required to complete the authentication process. Therefore, option A is true because the device is not configured for 802.1X authentication, which means that it does not have the correct credentials or settings to authenticate with the RADIUS server. Option D is also true because the device does not support 802.1X authentication, which means that it does not have the capability or software to perform 802.1X authentication. Option B is false because the device has not been quarantined for 3600 seconds, but rather has a session timeout of 3600 seconds, which is the default value for 802.1X sessions. Option C is false because the device has not been assigned the guest VLAN, but rather has been assigned the default VLAN, which is VLAN 1.
NEW QUESTION # 13
Which two statements about the guest portal on FortiAuthenticator are true? (Choose two.)
- A. Administrators must approve all guest accounts before they can be used
- B. Each remote user on FortiAuthenticator can sponsor up to 10 guest accounts
- C. Administrators can use one or more incoming parameters to configure a mapping rule for the guest portal
- D. The guest portal provides pre and post-log in services
Answer: C,D
Explanation:
Explanation
According to the FortiAuthenticator Administration Guide2, "The guest portal provides pre and post-log in services for users (such as password reset and token registration abilities), and rules and replacement messages can be configured." Therefore, option C is true. The same guide also states that "Administrators can use one or more incoming parameters to configure a mapping rule for the guest portal." Therefore, option D is true.
Option A is false because remote users can sponsor any number of guest accounts, as long as they do not exceed the maximum number of guest accounts allowed by the license. Option B is false because administrators can choose to approve or reject guest accounts, or enable auto-approval.
NEW QUESTION # 14
Exhibit.
Exhibit.
Refer to the exhibits
In the wireless configuration shown in the exhibits, an AP is deployed in a remote site and has a wireless network (VAP) called Corporate deployed to it The network is a tunneled network however clients connecting to a wireless network require access to a local printer Clients are trying to print to a printer on the remote site but are unable to do so Which configuration change is required to allow clients connected to the Corporate SSID to print locally?
- A. Disable the Block Intra-SSID Traffic (intra-vap-privacy) setting on the SSID (VAP) profile
- B. Configure the printer as a wireless client on the Corporate wireless network
- C. Configure split-tunneling in the wtp-profile configuration
- D. Configure split-tunneling in the vap configuration
Answer: D
Explanation:
Explanation
According to the Fortinet documentation1, "Split tunneling allows you to specify which traffic is tunneled to the FortiGate and which traffic is sent directly to the Internet. This can improve performance and reduce bandwidth usage." Therefore, by configuring split-tunneling in the vap configuration, you can allow the clients connected to the Corporate SSID to access both the corporate network and the local printer. Option B is incorrect because split-tunneling is configured at the vap level, not the wtp-profile level. Option C is incorrect because blocking intra-SSID traffic prevents wireless clients on the same SSID from communicating with each other, which is not related to accessing a local printer. Option D is unnecessary and impractical because the printer does not need to be a wireless client on the Corporate wireless network to be accessible by the clients.
NEW QUESTION # 15
Which two pieces of information can the diagnose test authserver ldap command provide? (Choose two.)
- A. It displays the LDAP codes returned by the LDAP server
- B. It displays whether the user credentials are correct
- C. It displays the LDAP groups found for the user
- D. It displays whether the admin bind user credentials are correct
Answer: A,B
Explanation:
Explanation
According to the FortiGate CLI Reference Guide, "The diagnose test authserver ldap command tests LDAP authentication with a specific LDAP server. The command displays whether the user credentials are correct and whether the user belongs to any groups that match a firewall policy. The command also displays the LDAP codes returned by the LDAP server." Therefore, options B and C are true because they describe the information that the diagnose test authserver ldap command can provide. Option A is false because the command does not display whether the admin bind user credentials are correct, but rather whether the user credentials are correct. Option D is false because the command does not display the LDAP groups found for the user, but rather whether the user belongs to any groups that match a firewall policy.
NEW QUESTION # 16
Which two statements about the MAC-based 802 1X security mode available on FortiSwitch are true? (Choose two.)
- A. FortiSwitch authenticates each device connected to the port
- B. FortiSwitch can grant different access levels to each device connected to the port
- C. FortiSwitch authenticates a single device and opens the port to other devices connected to the port
- D. It cannot be used in conjunction with MAC authentication bypass
Answer: A,B
Explanation:
Explanation
According to the FortiSwitch Administration Guide, "MAC-based 802.1X security mode allows you to authenticate each device connected to a port using its MAC address as the username and password." Therefore, option B is true because it describes the MAC-based 802.1X security mode available on FortiSwitch. Option D is also true because FortiSwitch can grant different access levels to each device connected to the port based on the user group and security policy assigned to them. Option A is false because FortiSwitch does not authenticate a single device and open the port to other devices connected to the port, but rather authenticates each device individually. Option C is false because MAC-based 802.1X security mode can be used in conjunction with MAC authentication bypass (MAB) or EAP pass-through modes, which are fallback options for non-802.1X devices.
NEW QUESTION # 17
Where can FortiGate learn the FortiManager IP address or FQDN for zero-touch provisioning'?
- A. From an LDAP server using a simple bind operation
- B. From a TFTP server
- C. From a DHCP server using options 240 and 241
- D. From a DNS server using A or AAAA records
Answer: D
Explanation:
Explanation
According to the FortiGate Administration Guide, "FortiGate can learn the FortiManager IP address or FQDN for zero-touch provisioning from a DNS server using A or AAAA records. The DNS server must be configured to resolve the hostname fortimanager.fortinet.com to the IP address or FQDN of the FortiManager device." Therefore, option D is true because it describes the method for FortiGate to learn the FortiManager IP address or FQDN for zero-touch provisioning. Option A is false because LDAP is not used for zero-touch provisioning. Option B is false because TFTP is not used for zero-touch provisioning. Option C is false because DHCP options 240 and 241 are not used for zero-touch provisioning.
NEW QUESTION # 18
Which two statements about FortiSwitchmanager are true1? (Choose two)
- A. If the administrator makes any changes on FortiSwitch manager they must also install those changes on FortiGate so that those changes are applied on the managed switches
- B. Any switch discovered or authorized on FortiGate must be added manually on FortiSwitch manager
- C. FortiManager obtains the FortiSwitch status information by querying the FortiGate REST API every three minutes
- D. Per-device management is the default management mode on FortiManager
Answer: A,C
Explanation:
Explanation
According to the FortiManager Administration Guide1, "FortiManager obtains the FortiSwitch status information by querying the FortiGate REST API every three minutes." Therefore, option B is true because it describes how FortiManager gets the information about the managed switches. According to the same guide2,
"If you make any changes in this module, you must install them on your managed device so that they are applied on your managed switches." Therefore, option C is true because it describes what the administrator must do after making any changes on FortiSwitch manager. Option A is false because central management is the default management mode on FortiManager, not per-device management. Option D is false because anyswitch discovered or authorized on FortiGate will be automatically added on FortiSwitch manager, not manually.
1: https://docs.fortinet.com/document/fortimanager/7.0.0/administration-guide/734537/fortiswitch-manager 2:
https://docs.fortinet.com/document/fortimanager/7.0.0/administration-guide/734537/fortiswitch-manager#fortisw
NEW QUESTION # 19
Refer to the exhibit
Examine the FortiGate RSSO configuration shown in the exhibit
FortiGate is configured to receive RADIUS accounting messages on port3 to authenticate RSSO users The users are located behind port3 and the internet link is connected to port1 FortiGate is processing incoming RADIUS accounting messages successfully and RSSO users are getting associated with the RSSO Group user group However all the users are able to access the internet, and the administrator wants to restrict internet access to RSSO users only Which configuration change should the administrator make to fix the problem?
- A. Add RSSO Group to the firewall policy
- B. Change the RADIUS Attribute Value selling to match the name of the RADIUS attribute containing the group membership information of the RSSO users
- C. Enable Security Fabric Connection on port3
- D. Create a second firewall policy from port3 lo port1 and select the target destination subnets
Answer: A
Explanation:
Explanation
According to the exhibit, the firewall policy from port3 to port1 has no user group specified, which means that it allows all users to access the internet. Therefore, option B is true because adding RSSO Group to the firewall policy will restrict internet access to RSSO users only. Option A is false because changing the RADIUS Attribute Value setting will not affect the firewall policy, but rather the RSSO user group membership. Option C is false because enabling Security Fabric Connection on port3 will not affect the firewall policy, but rather the communication between FortiGate and other Security Fabric devices. Option D is false because creating a second firewall policy from port3 to port1 will not affect the existing firewall policy, but rather create a redundant or conflicting policy.
NEW QUESTION # 20
An administrator is testing the connectivity for a new VLAN The devices in the VLAN are connected to a FortiSwitch device that is managed by FortiGate Quarantine is disabled on FortiGate While testing the administrator noticed that devices can ping FortiGate and FortiGate can ping the devices The administrator also noticed that inter-VLAN communication works However intra-VLAN communication does not work Which scenario is likely to cause this issue?
- A. The native VLAN configured on the ports is incorrect
- B. Access VLAN is enabled on the VLAN
- C. The FortiSwitch MAC address table is missing entries
- D. The FortiGate ARP table is missing entries
Answer: C
Explanation:
Explanation
According to the scenario, the devices in the VLAN are connected to a FortiSwitch device that is managed by FortiGate. Quarantine is disabled on FortiGate, which means that the devices are not blocked by any security policy. The devices can ping FortiGate and FortiGate can ping the devices, which means that the IP connectivity is working. Inter-VLAN communication works, which means that the routing between VLANs is working. However, intra-VLAN communication does not work, which means that the switching within the VLAN is not working. Therefore, option C is true because the FortiSwitch MAC address table is missing entries, which means that the FortiSwitch does not know how to forward frames to the destination MAC addresses within the VLAN. Option A is false because access VLAN is enabled on the VLAN, which means that the VLAN ID is added to the frames on ingress and removed on egress. This does not affect intra-VLAN communication. Option B is false because the native VLAN configured on the ports is incorrect, which means that the frames on the native VLAN are not tagged with a VLAN ID. This does not affect intra-VLAN communication. Option D is false because the FortiGate ARP table is missing entries, which means that FortiGate does not know how to map IP addresses to MAC addresses. This does not affect intra-VLAN communication.
NEW QUESTION # 21
Refer to the exhibits.
Firewall Policy
Examine the firewall policy configuration and SSID settings
An administrator has configured a guest wireless network on FortiGate using the external captive portal The administrator has verified that the external captive portal URL is correct However wireless users are not able to see the captive portal login page Given the configuration shown in the exhibit and the SSID settings which configuration change should the administrator make to fix the problem?
- A. Include the wireless client subnet range in the Exempt Source section
- B. Apply a guest.portal user group in the firewall policy with the ID 11.
- C. Disable the user group from the SSID configuration
- D. Enable the captivs-portal-exempt option in the firewall policy with the ID 11.
Answer: B
Explanation:
Explanation
According to the FortiGate Administration Guide, "To use an external captive portal, you must configure a user group that uses the external captive portal as the authentication method and apply it to a firewall policy." Therefore, option C is true because it will allow the wireless users to be redirected to the external captive portal URL when they try to access the Internet. Option A is false because disabling the user group from the SSID configuration will prevent the wireless users from being authenticated by the FortiGate device. Option B is false because enabling the captive-portal-exempt option in the firewall policy will bypass the captive portal authentication for the wireless users, which is not the desired outcome. Option D is false because including the wireless client subnet range in the Exempt Source section will also bypass the captive portal authentication for the wireless users, which is not the desired outcome.
NEW QUESTION # 22
Which CLI command should an administrator use to view the certificate verification process in real time?
- A. diagnose debug application foauthd -1
- B. diagnose debug application authd -1
- C. diagnose debug application radiusd -1
- D. diagnose debug application fnbamd -1
Answer: A
Explanation:
Explanation
According to the FortiOS CLI Reference Guide, "The diagnose debug application foauthd command enables debugging of certificate verification process in real time." Therefore, option A is true because it describes the CLI command that an administrator should use to view the certificate verification process in real time. Option B is false because diagnose debug application radiusd -1 enables debugging of RADIUS authentication process, not certificate verification process. Option C is false because diagnose debug application authd -1 enables debugging of authentication daemon process, not certificate verification process. Option D is false because diagnose debug application fnbamd -1 enables debugging of FSSO daemon process, not certificate verification process.
NEW QUESTION # 23
You are configuring a FortiGate wireless network to support automated wireless client quarantine using IOC Which two configurations must you put in place for a wireless client to be quarantined successfully? (Choose two)
- A. Configure the wireless network to be in tunnel mode
- B. Configure a firewall policy to allow communication
- C. Configure the wireless network to be in bridge mode
- D. Configure the FortiGate device in the Security Fabric with a FortiAnalyzer device
Answer: A,D
Explanation:
Explanation
According to the FortiGate Administration Guide, "To enable automated wireless client quarantine using IOC, you must configure the following settings: Configure your wireless network to be in tunnel mode. This allows FortiGate to inspect all wireless traffic and applysecurity policies. Configure your FortiGate device in the Security Fabric with a FortiAnalyzer device. This allows FortiAnalyzer to detect indicators of compromise (IOC) from wireless traffic and send quarantine commands to FortiGate." Therefore, options A and B are true because they describe the configurations that must be put in place for a wireless client to be quarantined successfully using IOC. Option C is false because configuring a firewall policy to allow communication is not required, as the default firewall policy for tunnel mode wireless networks is to allow all traffic. Option D is false because configuring the wireless network to be in bridge mode is not supported, as FortiGate cannot inspect or quarantine wireless traffic in bridge mode.
NEW QUESTION # 24
Refer to the exhibits
The exhibits show the wireless network (VAP) SSID profiles defined on FortiManager and an AP profile assigned to a group of APs that are supported by FortiGate None of the APs are broadcasting the SSlDs defined by the AP profile Which changes do you need to make to enable the SSIDs to broadcast?
- A. In the SSIDs section enable Tunnel
- B. In the SSIDs section enable Manual and assign the networks manually
- C. Enable multiple channels in the Channels section and enable Radio Resource Provision
- D. Enable one channel in the Channels section
Answer: D
Explanation:
Explanation
According to the FortiManager Administration Guide1, "To enable the SSID, you must select at least one channel for the radio. If no channels are selected, the SSID will not be enabled." Therefore, enabling one channel in the Channels section will allow the SSIDs to broadcast.
NEW QUESTION # 25
Which CLI command should an administrator use to view the certificate verification process in real time?
- A. diagnose debug application foauthd -1
- B. diagnose debug application authd -1
- C. diagnose debug application radiusd -1
- D. diagnose debug application fnbamd -1
Answer: A
Explanation:
Explanation
According to the FortiOS CLI Reference Guide, "The diagnose debug application foauthd command enables debugging of certificate verification process in real time." Therefore, option A is true because it describes the CLI command that an administrator should use to view the certificate verification process in real time. Option B is false because diagnose debug application radiusd -1 enables debugging of RADIUS authentication process, not certificate verification process. Option C is false because diagnose debug application authd -1 enables debugging of authentication daemon process, not certificate verification process. Option D is false because diagnose debug application fnbamd -1 enables debugging of FSSO daemon process, not certificate verification process.
NEW QUESTION # 26
Refer to the exhibit.
Examine the FortiManager configuration and FortiGate CLI output shown in the exhibit An administrator is testing the NAC feature The test device is connected to a managed FortiSwitch device
{S224EPTF19"53C7)onpOrt2
After applying the NAC policy on port2 and generating traffic on the test device the test device is not matching the NAC policy therefore the test device remains m the onboarding VLAN Based on the information shown in the exhibit which two scenarios are likely to cause this issue? (Choose two.)
- A. The device operating system detected by FortiGate is not Linux
- B. The MAC address configured on the NAC policy is incorrect
- C. Management communication between FortiGate and FortiSwitch is down
- D. Device detection is not enabled on VLAN 4089
Answer: B,C
Explanation:
Explanation
According to the FortiManager configuration, the NAC policy is set to match devices with the MAC address of 00:0c:29:6a:2b:3c and the operating system of Linux.However, according to the FortiGate CLI output, the test device has a different MAC address of 00:0c:29:6a:2b:3d. Therefore, option B is true. Option A is also true because the FortiSwitch device status is shown as down, which means that the management communication between FortiGate and FortiSwitch is not working properly. This could prevent the NAC policy from being applied correctly. Option C is false because the device operating system detected by FortiGate is Linux, which matches the NAC policy. Option D is false because device detection is enabled on VLAN 4089, as shown by the command "config switch-controller vlan".
NEW QUESTION # 27
......
Quickly and Easily Pass Fortinet Exam with NSE7_LED-7.0 real Dumps: https://www.topexamcollection.com/NSE7_LED-7.0-vce-collection.html
Realistic NSE7_LED-7.0 Dumps Questions To Gain Brilliant Result: https://drive.google.com/open?id=1hqyAHWmYqj54ASnW4eDPrXWCjbUHItGq
